|
實驗室校準方法和程序 - 卡尺的校準
0 mm to 300 mm BS 887: 2008 # BS 887: 1982 # 在以下範圍內: 外部測量 : 0 mm to 300 mm 內部測量: 10 mm to 300 mm In-house method GEN-L-002 * 實驗室校準方法和程序 - 塞尺/厚度計的校準 0.01 mm to 1 mm BS 957: 2008 # 實驗室校準方法和程序 - 捲尺的校準 0 m to 5 m BS 4035: 1966 # 實驗室校準方法和程序 - 千分錶 / 百分錶和位移傳感器的校準 0 mm to 50 mm BS 907:2008 # 實驗室校準方法和程序 - 鋼尺 1 mm to 1000 mm In-house method GEN-L-007 * BS 4372:1968 # 實驗室校準方法和程序 - 角尺 0 mm to 160 mm BS 939:2007 # 實驗室校準方法和程序 -坍落度桶 (士冧桶) 直徑: 0 mm to 200 mm 厚度: ≥1.5 mm 高度: 0 mm to 300 mm In-house method CON-L-009 * CS1: 1990 Vol.1 A4; # CS1: 2010 Vol. 1, A5 #* BS EN 12350-2: 2009 Cl. 4.1 #* BS EN 12350-1: 2019 Cl. 4.1.7 # 實驗室校準方法和程序 - 磚模 (每邊最大尺寸 150 毫米) 尺寸 平整度 垂直度 平行性 In-house method CON-L-003 * BS1881: Part 108:1983; # CS1:1990 Vol1, A21; # CS1:2010 Vol 1, A25; #* BS EN 12390-1:2000 Cl. 5.2.4 #* BS EN 12390-1: 2012 Cl. 5.2.4 # BS EN 12390-1: 2021 Cl. 5.2.2 # 實驗室校準方法和程序 - 壓實桿 撞擊面: 25 mm 長度: 380 mm 重量: 1.8 kg In-house method CON-L-011 * BS 1881: Part 105: 1984 Cl 3.3; # CS1: 1990 Vol 2, E3; # CS1: 2010 Vol 1 A10; #* BS EN 12390-2: 2000 Cl 3.3; #* BS EN 12350-1: 2019 Cl. 4.1.8 # 實驗室校準方法和程序 - 保護層厚測定儀 20 mm to 103 mm BS 1881 204:1988 Cl.6.4- Method C # 實驗室校準方法和程序 - 流度台 重量：15 kg至 17 kg 尺寸：1 mm至 71 cm BS 1881- Part 105: 1984 # 實驗室校準方法和程序 - 測試篩 4 mm to 50 mm BS 410 : 1986 # 實驗室校準方法和程序 - 延伸計 延伸計之間的間隙 10 毫米至 100 毫米 BS 812- Part 1:1975; # BS 812- Part 105.2: 1990 # 實驗室校準方法和程序 - 剝落度測量器 量規槽長 4.9 mm至 33.9 mm BS 812- Part 1:1975; # BS 812- Part105.1:1985; # BS 812- Part105.1:1989 # 實驗室校準方法和程序 - 樣品分隔盒 寬度 6 mm至 100 mm BS 812- Part 1:1975 # * Hoklas 認證報告 # IAS 認證報告 Laboratory calibration method and procedure - calibration of caliper
0 mm to 300 mm BS 887: 2008 # BS 887: 1982 # Over the following ranges : External measurement : 0 mm to 300 mm Internal measurement: 10 mm to 300 mm In-house method GEN-L-002 * Laboratory calibration method and procedure - calibration of feeler / thickness gauge 0.01 mm to 1 mm BS 957: 2008 # Laboratory calibration method and procedure - calibration of measuring tape 0 m to 5 m BS 4035: 1966 # Laboratory calibration method and procedure - calibration of dial gauges and Gauge 0 mm to 50 mm BS 907:2008 # Laboratory calibration method and procedure - calibration of Steel Ruler 1 mm to 1000 mm In-house method GEN-L-007 * BS 4372:1968 # Laboratory calibration method and procedure - Engineering Square 0 mm to 160 mm BS 939:2007 # Laboratory calibration method and procedure - Slump cone Diameter: 0 mm to 200 mm Thickness: ≥1.5 mm Height: 0 mm to 300 mm In-house method CON-L-009 * CS1: 1990 Vol.1 A4; # CS1: 2010 Vol. 1, A5 #* BS EN 12350-2: 2009 Cl. 4.1 #* BS EN 12350-1: 2019 Cl. 4.1.7 # Laboratory calibration method and procedure - Cube mould (Max dimensions 150 mm per side) Dimension Flatness Perpendicularity Parallelism In-house method CON-L-003 * BS1881: Part 108:1983; # CS1:1990 Vol1, A21; # CS1:2010 Vol 1, A25; #* BS EN 12390-1:2000 Cl. 5.2.4 #* BS EN 12390-1: 2012 Cl. 5.2.4 # BS EN 12390-1: 2021 Cl. 5.2.2 # Laboratory calibration method and procedure - Compacting Bar Ramming Face: 25 mm Length: 380 mm Weight: 1.8 kg In-house method CON-L-011 * BS 1881: Part 105: 1984 Cl 3.3; # CS1: 1990 Vol 2, E3; # CS1: 2010 Vol 1 A10; #* BS EN 12390-2: 2000 Cl 3.3; #* BS EN 12350-1: 2019 Cl. 4.1.8 # Laboratory calibration method and procedure - Tamping rod Diameter of rod: 16 mm Length of rod: 600 mm In-house method CON-L-009 * Laboratory calibration method and procedure - Covermeter 20 mm to 103 mm BS 1881 204:1988 Cl.6.4- Method C # Laboratory calibration method and procedure - Flow table Mass 15 kg to 17 kg Dimension 1 mm up to 71 cm BS 1881- Part 105: 1984 # Laboratory calibration method and procedure - Test Sieve 4 mm to 50 mm BS 410 : 1986 # Laboratory calibration method and procedure - Elongation Gauge Gap between Pins of Gauge 10 mm to 100 mm BS 812- Part 1:1975; # BS 812- Part 105.2: 1990 # Laboratory calibration method and procedure - Flakiness Gauge Length of Slot of Gauge 4.9 mm to 33.9 mm BS 812- Part 1:1975; # BS 812- Part105.1:1985; # BS 812- Part105.1:1989 # Laboratory calibration method and procedure - Riffle Box Width 6 mm to 100 mm BS 812- Part 1:1975 # * Hoklas accredited report # IAS accredited report |
|